- HOW TO MOUNT AFATECH IN LINUX INSTALL
- HOW TO MOUNT AFATECH IN LINUX DRIVER
- HOW TO MOUNT AFATECH IN LINUX SOFTWARE
- HOW TO MOUNT AFATECH IN LINUX WINDOWS
K-VoxĮxamples of DVB-T USB devices in which the AF9015 chip can be found include: or perhaps start a new article for the AF901x family, and leave this one dedicated to the AF9015)ĭIGIVOX mini II V3.0 (AF9015/MT2060 version) aka. The AF901x family consists of the following chips: Unfortunately, tuner devices build on these chips are known to be unstable demanding frequent cold boots. Documentation for the AF901x family can be obtained from AFA (under NDA), but it is apparently confusing, as well as incomplete - as there are a lot of areas that are undocumented.
HOW TO MOUNT AFATECH IN LINUX WINDOWS
It is also very flexible, supporting a wide variety of device configurations (single USB, dual USB, Platform mode, PCI/PCIe based devices, and even SPI is supported by it with some tuners (such as for a Consumer Electronics product that runs Windows CE)). Given the chip's dual nature, the AF9015 is fairly complex. This is the company's second generation COFDM demodulator, and is the successor to the AF900x family of chips. It can be played back with for instance VLC.A combination DVB-T demodulator and USB bridge chip from Afatech. Which saves the channel to the file /root/tv. Then I launched xine sudo xine -H -V none -A none dvb://#save:tv When running as sudo, xine gets confused and takes some config files from my home-dir and some from /root.Įdit /root/.xine/config and set the _dir for instance to /root. # scan /usr/local/share/dvbv3/dvb-t/se-Stockholm_Nacka \ Plus some other dvb packet and did git clone git:///dtv-scan-tables.gitĪnd then put the channels file in the right place. It needs channel files of version v3, so I installed the dvb-apps packages
HOW TO MOUNT AFATECH IN LINUX INSTALL
I installed xine with apt-get install xine-ui usb 1-1: dvb_usb_v2: 'Afatech AF9035 reference design' successfully initialized and connected i2c i2c-0: Fitipower FC0011 tuner attached usb 1-1: DVB: registering adapter 0 frontend 0 (Afatech AF9033 (DVB-T)). DVB: registering new adapter (Afatech AF9035 reference design)
HOW TO MOUNT AFATECH IN LINUX SOFTWARE
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer usb 1-1: dvb_usb_v2: found a 'Afatech AF9035 reference design' in warm state usb 1-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-af9035-02.fw' I removed and reinserted the dongle, and got the dmesg messages usb 1-1: new high-speed USB device number 4 using ehci-pci I downloaded and checked the checksum with md5sum and put the file in /lib/firmware/dvb-usb-af9035-02.fw The last page says that the firmware can be downloaded from
HOW TO MOUNT AFATECH IN LINUX DRIVER
usbcore: registered new interface driver usbhid hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver dvb_usb_af9035 dvb_usb_af9035: probe of 1-1:1.0 failed with error -2 Please see linux/Documentation/dvb/ for more details on firmware-problems. usb 1-1: dvb_usb_v2: Did not find the firmware file 'dvb-usb-af9035-02.fw'. usb 1-1: Direct firmware load failed with error -2 usb 1-1: dvb_usb_v2: found a 'Afatech AF9035 reference design' in cold state usb 1-1: dvb_usb_af9035: prechip_version=ff chip_version=f8 chip_type=f790 usb 1-1: Manufacturer: Afa Technologies Inc. usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: New USB device found, idVendor=15a4, idProduct=1001 Plugging the dongle out and in again, gives these messages: usb 1-1: new high-speed USB device number 2 using ehci-pci It tells the usbhid driver to ignore (0x0004) the device. HID driver from taking control over the device by adding the line options usbhid quirks=0x15a4:0x1001:0x0004 NOTE: JUST FOR REFERENCE FOR OLDER KERNELS: If you have an old linux that thinks it is a HID (Human input device), a keyboard, you can stop the After plugging it in to linux lsusb shows me Bus 001 Device 004: ID 15a4:1001 Afatech Technologies, Inc.
0 kommentar(er)
